BenchK Installation Kit

Exclusively for use with BenchK 2, 5, 7  Series wall bars, these wall holders are highly recommended for ensuring the most stable, secure installation possible in case of the wooden studs wall construction. Each wall holder is made in Poland from laser-cut and formed steel brackets. Within the pair, one holder is used to mount the top of the BenchK wall bars and the other for the bottom.

The wall holders for the BenchK wall bars are designed with special pre-cut slots, allowing users to mount them to a standard wood stud wall (2 studs required for installation and 8 screws that have to be purchased separately). Thanks to the with of the pre-cut slots, the holders can be adjusted to the distance between the wooden studs. Remember that the Fischer plugs and screws are not suitable for wood installation.

A well-known German manufacturer of fastening systems offers DUOPOWER pins – which guarantee very good fixing thanks to the use of 2 components: depending on the base material, the gray element made of high-quality nylon automatically activates the optimal holding function (expanding, folding, rolling) for the best fixing.

The spreader wings of the red element provide expansion and additional protection of the gray element. Easily screwed in and tightened at the end. No risk of over-tightening the pin. The molded edge of the pin prevents it from falling into the hole.

Advantages

• Two different components allow for the highest load-bearing capacities and intelligent operation in different types of ground.
• Good feeling when the pin is fully extended. You can feel the exact moment when the pin is properly fitted.
• A small collar on the periphery of the plug prevents it from falling into the hole during assembly.
• Serrated shape on the side of the plug prevents it from turning during assembly.
• Increased anchoring depth makes the plug particularly suitable for fixing in hollow blocks, aerated concrete and plastered walls.

Assembly instructions and operation.

When required, most assemblies are relatively easy to perform. Some require a higher skill level.

If you prefer not to handle the setup, you may outsource this task to our trusted partners anywhere in the USA. Contact Us for details.

• DUOPOWER pins are suitable for both pre-assembly and push-through assembly.
• The combination of two different materials of the dowel affects their various properties (expansion, folding and looping), which allows the use of additional substrates and obtaining the highest load capacity in them.
• The required screw length results from the length of the plug + thickness of the fastened element + 1x screw diameter.
• Wood screws, chipboard screws and hanger bolts can be used for the dowels.
• In the case of fastening to board materials, the unthreaded part of the screw must not be longer than the thickness of the fastened element.
• It is not recommended to use when the thickness of the wall is less than 12 cm (4,7″).

Instructions (Manual & Video)

See/Download the manual

View our Instruction Video

Specifications

Wall holder:
Dimensions: 66cm x 10cm x 10cm (25,9”x 3,9” x 3,9”)
Weight: 4 kg (8,8 lbs)
Color: black matt
Material: steel
Warranty for steel elements: 10 years

S8
8 sets (screw and plastic cover)
Minimum wall thicnkess is 12 cm

Use only when the wall is solid:
Concrete Solid bricks
Solid silicate bricks
Aerated concreto
Bricks with vertical perforation
Perforated silicate bricks
Plasterboard
Gypsum plasterboards and gypsum fiber boards
Light concrete hollow block blocks
Hollow-core slabs of brick and concrete or the like
Natural stone
Particle boards
Full gypsum boards

Exclusively for use with BenchK 2, 5, 7  Series wall bars, these wall holders are highly recommended for ensuring the most stable, secure installation possible in case of the wooden studs wall construction. Each wall holder is made in Poland from laser-cut and formed steel brackets. Within the pair, one holder is used to mount the top of the BenchK wall bars and the other for the bottom.

The wall holders for the BenchK wall bars are designed with special pre-cut slots, allowing users to mount them to a standard wood stud wall (2 studs required for installation and 8 screws that have to be purchased separately). Thanks to the with of the pre-cut slots, the holders can be adjusted to the distance between the wooden studs. Remember that the Fischer plugs and screws are not suitable for wood installation.

A well-known German manufacturer of fastening systems offers DUOPOWER pins – which guarantee very good fixing thanks to the use of 2 components: depending on the base material, the gray element made of high-quality nylon automatically activates the optimal holding function (expanding, folding, rolling) for the best fixing.

The spreader wings of the red element provide expansion and additional protection of the gray element. Easily screwed in and tightened at the end. No risk of over-tightening the pin. The molded edge of the pin prevents it from falling into the hole.

Advantages

• Two different components allow for the highest load-bearing capacities and intelligent operation in different types of ground.
• Good feeling when the pin is fully extended. You can feel the exact moment when the pin is properly fitted.
• A small collar on the periphery of the plug prevents it from falling into the hole during assembly.
• Serrated shape on the side of the plug prevents it from turning during assembly.
• Increased anchoring depth makes the plug particularly suitable for fixing in hollow blocks, aerated concrete and plastered walls.

Assembly instructions and operation.

When required, most assemblies are relatively easy to perform. Some require a higher skill level.

If you prefer not to handle the setup, you may outsource this task to our trusted partners anywhere in the USA. Contact Us for details.

• DUOPOWER pins are suitable for both pre-assembly and push-through assembly.
• The combination of two different materials of the dowel affects their various properties (expansion, folding and looping), which allows the use of additional substrates and obtaining the highest load capacity in them.
• The required screw length results from the length of the plug + thickness of the fastened element + 1x screw diameter.
• Wood screws, chipboard screws and hanger bolts can be used for the dowels.
• In the case of fastening to board materials, the unthreaded part of the screw must not be longer than the thickness of the fastened element.
• It is not recommended to use when the thickness of the wall is less than 12 cm (4,7″).

Instructions (Manual & Video)

See/Download the manual

View our Instruction Video

Specifications

Wall holder:
Dimensions: 66cm x 10cm x 10cm (25,9”x 3,9” x 3,9”)
Weight: 4 kg (8,8 lbs)
Color: white matt
Material: steel
Warranty for steel elements: 10 years

S8
8 sets (screw and plastic cover)
Minimum wall thicnkess is 12 cm

Use only when the wall is solid:
Concrete Solid bricks
Solid silicate bricks
Aerated concreto
Bricks with vertical perforation
Perforated silicate bricks
Plasterboard
Gypsum plasterboards and gypsum fiber boards
Light concrete hollow block blocks
Hollow-core slabs of brick and concrete or the like
Natural stone
Particle boards
Full gypsum boards

Exclusively for use with wooden BenchK 1 Series wall bars, these wall holders are highly recommended for ensuring the most stable, secure installation possible in case of the wooden studs wall construction. Each wall holder is made in Poland from laser-cut and formed steel brackets. Within the pair, one holder is used to mount the top of the BenchK wall bars and the other for the bottom.

The wall holders for the BenchK wall bars are designed with special pre-cut slots, allowing users to mount them to a standard wood stud wall (2 studs required for installation and 4 screws that have to be purchased separately). Thanks to the with of the pre-cut slots, the holders can be adjusted to the distance between the wooden studs. Remember that the Fischer plugs and screws available at www.benchk.us are not suitable for wood installation.

A well-known German manufacturer of fastening systems offers DUOPOWER pins – which guarantee very good fixing thanks to the use of 2 components: depending on the base material, the gray element made of high-quality nylon automatically activates the optimal holding function (expanding, folding, rolling) for the best fixing.

The spreader wings of the red element provide expansion and additional protection of the gray element. Easily screwed in and tightened at the end. No risk of over-tightening the pin. The molded edge of the pin prevents it from falling into the hole.

Advantages

• Two different components allow for the highest load-bearing capacities and intelligent operation in different types of ground.
• Good feeling when the pin is fully extended. You can feel the exact moment when the pin is properly fitted.
• A small collar on the periphery of the plug prevents it from falling into the hole during assembly.
• Serrated shape on the side of the plug prevents it from turning during assembly.
• Increased anchoring depth makes the plug particularly suitable for fixing in hollow blocks, aerated concrete and plastered walls.

Assembly instructions and operation.

• DUOPOWER pins are suitable for both pre-assembly and push-through assembly.
• The combination of two different materials of the dowel affects their various properties (expansion, folding and looping), which allows the use of additional substrates and obtaining the highest load capacity in them.
• The required screw length results from the length of the plug + thickness of the fastened element + 1x screw diameter.
• Wood screws, chipboard screws and hanger bolts can be used for the dowels.
• In the case of fastening to board materials, the unthreaded part of the screw must not be longer than the thickness of the fastened element.
• It is not recommended to use when the thickness of the wall is less than 12 cm (4,7″).

Specifications

Wall holder:
Dimensions: 58cm x 6cm x 12cm / 22,8”x 2,3” x 4,7”
Weight:  2 kg (4,4 lbs)
Color: black matt
Material: steel
Warranty for steel elements: 10 years

S4
4 sets (screw and plastic cover)
Minimum wall thickness is: 12cm
Use with BenchK 1 series

Use only when the wall is solid:
Concrete
Solid bricks
Solid silicate bricks
Aerated concreto
Bricks with vertical perforation
Perforated silicate bricks
Plasterboard
Gypsum plasterboards and gypsum fiber boards
Light concrete hollow block blocks
Hollow-core slabs of brick and concrete or the like
Natural stone
Particle boards
Full gypsum boards
For stud frame wall construction do not use plastic plugs

Assembly instructions

A well-known German manufacturer of fastening systems offers DUOPOWER pins – which guarantee very good fixing thanks to the use of 2 components: depending on the base material, the gray element made of high-quality nylon automatically activates the optimal holding function (expanding, folding, rolling) for the best fixing.

The spreader wings of the red element provide expansion and additional protection of the gray element. Easily screwed in and tightened at the end. No risk of over-tightening the pin. The molded edge of the pin prevents it from falling into the hole.

The set consisting of 12 sets (dowel with screw) is used in the following series:

• BenchK 7

Advantages

• Two different components allow for the highest load-bearing capacities and intelligent operation in different types of ground.
• Good feeling when the pin is fully extended. You can feel the exact moment when the pin is properly fitted.
• A small collar on the periphery of the plug prevents it from falling into the hole during assembly.
• • Serrated shape on the side of the plug prevents it from turning during assembly.
• Increased anchoring depth makes the plug particularly suitable for fixing in hollow blocks, aerated concrete and plastered walls.

Application

• Concrete
• Solid bricks
• Solid silicate bricks
• Aerated concrete
• Bricks with vertical perforation
• Perforated silicate bricks
• Plasterboard
• Gypsum plasterboards and gypsum fiber boards
• Light concrete hollow block blocks
• Hollow-core slabs of brick and concrete or the like
• Natural stone
• Particle boards
• Full gypsum boards

Solid bricks made of lightweight concrete

Assembly instructions and operation.

• DUOPOWER pins are suitable for both pre-assembly and push-through assembly.
• The combination of two different materials of the dowel affects their various properties (expansion, folding and looping), which allows the use of additional substrates and obtaining the highest load capacity in them.
• The required screw length results from the length of the plug + thickness of the fastened element + 1x screw diameter.
• Wood screws, chipboard screws and hanger bolts can be used for the dowels.
• In the case of fastening to board materials, the unthreaded part of the screw must not be longer than the thickness of the fastened element.
• It is not recommended to use when the thickness of the wall is less than 12 cm (4,7″).

Assembly instructions (Video)

Specifications

A well-known German manufacturer of fastening systems offers DUOPOWER pins – which guarantee very good fixing thanks to the use of 2 components: depending on the base material, the gray element made of high-quality nylon automatically activates the optimal holding function (expanding, folding, rolling) for the best fixing.

The spreader wings of the red element provide expansion and additional protection of the gray element. Easily screwed in and tightened at the end. No risk of over-tightening the pin. The molded edge of the pin prevents it from falling into the hole.

The set consisting of 8 sets (dowel with screw) is used in the following series:

• BenchK 1
• BenchK 2
• BenchK 5

We invite you to watch the instructional video

Advantages

• Two different components allow for the highest load-bearing capacities and intelligent operation in different types of ground.
• Good feeling when the pin is fully extended. You can feel the exact moment when the pin is properly fitted.
• A small collar on the periphery of the plug prevents it from falling into the hole during assembly.
• Serrated shape on the side of the plug prevents it from turning during assembly.
• Increased anchoring depth makes the plug particularly suitable for fixing in hollow blocks, aerated concrete and plastered walls.

Application

• Concrete
• Solid bricks
• Solid silicate bricks
• Aerated concrete
• Bricks with vertical perforation
• Perforated silicate bricks
• Plasterboard
• Gypsum plasterboards and gypsum fiber boards
• Light concrete hollow block blocks
• Hollow-core slabs of brick and concrete or the like
• Natural stone
• Particle boards
• Full gypsum boards

Solid bricks made of lightweight concrete

Assembly instructions and operation.

• DUOPOWER pins are suitable for both pre-assembly and push-through assembly.
• The combination of two different materials of the dowel affects their various properties (expansion, folding and looping), which allows the use of additional substrates and obtaining the highest load capacity in them.
• The required screw length results from the length of the plug + thickness of the fastened element + 1x screw diameter.
• Wood screws, chipboard screws and hanger bolts can be used for the dowels.
• In the case of fastening to board materials, the unthreaded part of the screw must not be longer than the thickness of the fastened element.
• It is not recommended to use when the thickness of the wall is less than 12 cm (4,7″).

Assembly instructions (Video)

Specifications